Tips for Uploading Firmware
Uploading firmware to an AREDN® node is usually a straightforward process. Follow the procedures documented in the Downloading AREDN Firmware section to ensure you have the correct firmware version from the AREDN® website to install on your node. If you experience issues uploading firmware, the following tips may be helpful.
- Error message when uploading firmware
If you see an error message displayed when uploading new firmware to your node, verify that you are loading the correct file by referring to the AREDN download page, then you can safely ignore the warning. The file naming standard recently changed from a non-standard naming convention to the standard naming convention used by OpenWRT.
- Web browser cache and sessions
One common issue can occur when installing firmware using a web browser. Your computer’s browser cache stores data for the URLs that have been visited, but IP addresses and other parameters may change during the install process. It is possible for the cache to contain information that doesn’t match the latest settings for the URL, so the browser may block the connection setup and display an ERR_CONNECTION_RESET message. Clearing your computer’s web browser cache will allow the latest URL settings to be registered so you can continue with the install process.
Instead of a Connection Reset message, sometimes a Bad Gateway message may appear. This is an HTTP Status Code that can mean any of several things. Often it indicates a network communication issue between a web browser and a web server. During AREDN® firmware installs you can usually resolve a Bad Gateway issue by doing one or more of the following things:
Refresh or Reload the URL for your node.
Clear your browser cache and delete cookies.
Close your browser and restart a new session.
Use a different web browser program or a Safe Mode / Incognito browser window.
Unplug and reconnect the Ethernet cable from your computer to ensure that your machine has received a new DHCP IP address on the same subnet as the node’s updated IP.
- PXE Server
If you are using a PXE server to provide your device with an IP address and a new firmware image, be sure to allow the PXE server through your computer’s firewall. If the PXE server does not display any activity when you begin your firmware install, check your firewall settings. On the Windows control panel, for example, click Advanced Settings and look through the “Inbound Rules” to see if a rule exists for the PXE server. If a rule exists, make sure to “allow connection” for both private and public networks. If no rule exists, create a new rule allowing connection for both public and private networks.
Tips for Upgrading
Upgrading an AREDN® node is accomplished using the Setup > Administration > Firmware Update feature on the node’s web interface. Follow the procedures documented in the Downloading AREDN Firmware section to ensure you have the correct firmware version from the AREDN® website to install on your node.
In rare cases the upgrade process can fail due to lack of memory, but such a failure will leave the node running its previous firmware version. The following tips help ensure that memory utilization is at a minimum on the node.
- Release node resources
Before starting the firmware upgrade on low memory devices, it may be necessary to stop, disable, or uninstall extra packages such as Meshchat, snmp, and tunneling. The goal of this step is to keep those processes from using RAM memory and to free as much RAM as possible before the upgrade. Rebooting the node before beginning the upgrade will ensure that RAM utilization is at a minimum.
You may also want to stop node programs or services that are not needed during the upgrade. For example, you can telnet or ssh to the node and type the command
wifi downto free the memory used by this driver.
- Tips for legacy nodes with low memory (32mb)
Legacy equipment with only 32mb of memory may require more effort to upgrade. Be sure not to use these types of devices at sites which are difficult to access.
You may need to try the sysupgrade procedure several times before it succeeds. Be patient and keep trying.
Get everything ready to do the upgrade, then do a fresh reboot of the node and immediately start the sysupgrade process before the node has time to initialize services which use memory.
Use command line access to copy the sysupgrade.bin image to the /tmp directory on the node, then run the sysupgrade process manually from the command line on the node. Note that AREDN® nodes use port 2222 for secure copy and secure shell access.
Execute the following commands from a Linux computer:
>>> my-computer:$ scp -P 2222 aredn-firmware-filename.bin email@example.com:/tmp my-computer:$ ssh -p 2222 firstname.lastname@example.org ~~~~~~~ after logging into the node with ssh ~~~~~~~ node:# sysupgrade /tmp/aredn-firmware-filename.bin
To transfer the image from a Windows computer you can use a Secure Copy program such as WinSCP. Then use a terminal program such as PuTTY to connect to the node via ssh or telnet in order to run the sysupgrade command shown as the last line above.
As a last resort, use the TFTP procedure to load the factory.bin firmware image to the node. This procedure is described in the First Install sections of Installing AREDN Firmware.