Tips for Uploading Firmware
Uploading firmware to an AREDN® node is usually a straightforward process. Follow the procedures documented in the Downloading AREDN Firmware section to ensure you have the correct firmware version from the AREDN® website to install on your node. If you experience issues uploading firmware, the following tips may be helpful.
- Error message when uploading firmware
- If you see an error message displayed when uploading new firmware to your node, verify that you are loading the correct file by referring to the AREDN Firmware Selector (AFS), then you can safely ignore the warning. The file naming standard recently changed from a non-standard naming convention to the standard naming convention used by OpenWRT.
- Web browser cache and sessions
One common issue can occur when installing firmware using a web browser. Your computer’s browser cache stores data for the URLs that have been visited, but IP addresses and other parameters may change during the install process. It is possible for the cache to contain information that doesn’t match the latest settings for the URL, so the browser may block the connection setup and display an ERR_CONNECTION_RESET message. Clearing your computer’s web browser cache will allow the latest URL settings to be registered so you can continue with the install process.
Instead of a Connection Reset message, sometimes a Bad Gateway message may appear. This is an HTTP Status Code that can mean any of several things. Often it indicates a network communication issue between a web browser and a web server. During AREDN® firmware installs you can usually resolve a Bad Gateway issue by doing one or more of the following things:
- Refresh or Reload the URL for your node.
- Clear your browser cache and delete cookies.
- Close your browser and restart a new session.
- Use a different web browser program or a Safe Mode / Incognito browser window.
- Unplug and reconnect the Ethernet cable from your computer to ensure that your machine has received a new DHCP IP address on the same subnet as the node’s updated IP.
- PXE Server
- If you are using a PXE server to provide your device with an IP address and a new firmware image, be sure to allow the PXE server through your computer’s firewall. If the PXE server does not display any activity when you begin your firmware install, check your firewall settings. On the Windows control panel, for example, click Advanced Settings and look through the “Inbound Rules” to see if a rule exists for the PXE server. If a rule exists, make sure to “allow connection” for both private and public networks. If no rule exists, create a new rule allowing connection for both public and private networks.
Tips for Upgrading Firmware
Upgrading an AREDN® node is accomplished using the Setup > Administration > Firmware Update feature on the node’s web interface. Follow the procedures documented in the Downloading AREDN Firmware section to ensure you have the correct firmware version from the AREDN® website to install on your node.
Currently there are two Mikrotik devices which require that the standard firmware compatibility checks be disabled in order to upgrade from version 184.108.40.206 or older to a newer firmware version. The specific devices are shown in the Supported Devices list on the AREDN® website with a Status of danger-upgrade, and the notes at the bottom of that page explain what is required. You must first install the Dangerous Upgrade package (the ipk file) which will disable the firmware compatibility checks. After this package is installed on your node you can perform a normal firmware upgrade (for example) from 220.127.116.11 to 18.104.22.168.
In rare cases the upgrade process can fail due to lack of node resources, but such a failure will leave the node running its previous firmware version. The following tips help ensure that memory utilization is at a minimum on the node.
- Try to Load Local Firmware
- The Load Local Firmware option is described in the Configuration Deep Dive > Administration documentation. This involves using a file copy utility on your computer to copy the firmware file to a specific directory and filename on your node. Once the new firmware file is available on the node, you can click the Load Local Firmware button to start the install process.
- Tips for legacy nodes with low memory (32mb)
Legacy equipment with only 32mb of memory may require more effort to upgrade. Be sure not to use these types of devices at sites which are difficult to access.
Before starting the firmware upgrade on low memory devices, it may be necessary to stop, disable, or uninstall extra packages such as MeshChat, SNMP, and IperfSpeed. The goal of this step is to keep those processes from using RAM memory and to free as much RAM as possible before the upgrade. Rebooting the node before beginning the upgrade will ensure that RAM utilization is at a minimum.
You may also want to stop node programs or services that are not needed during the upgrade. For example, you can telnet or ssh to the node and type the command
wifi downto free the memory used by this driver.
You may need to try the sysupgrade procedure several times before it succeeds. Be patient and keep trying.
Get everything ready to do the upgrade, then do a fresh reboot of the node and immediately start the sysupgrade process before the node has time to initialize services which use memory.
Use command line access to copy the sysupgrade.bin image to the /tmp directory on the node, then run the sysupgrade process manually from the command line on the node. Note that AREDN® nodes use port 2222 for secure copy and secure shell access.
Execute the following commands from a Linux computer:
my-computer:$ scp -P 2222 aredn-firmware-filename.bin firstname.lastname@example.org:/tmp my-computer:$ ssh -p 2222 email@example.com ~~~~~~~ after logging into the node with ssh ~~~~~~~ node:# sysupgrade /tmp/aredn-firmware-filename.bin
To transfer the image from a Windows computer you can use a Secure Copy program such as WinSCP. Then use a terminal program such as PuTTY to connect to the node via ssh or telnet in order to run the sysupgrade command shown as the last line above.
As a last resort, use the First Install procedure to load the factory.bin firmware image to the node. This procedure is described in the First Install sections of Installing AREDN Firmware.
Tips for Downgrading Firmware
Downgrading AREDN® firmware is typically accomplished using the same procedure as for uploading firmware to your node. You are simply uploading a previous version of the firmware rather than the latest version.
However, there is a difference if you are downgrading the firmware on a node which previously used a different target architecture. As explained in the Downloading AREDN Firmware section, the legacy
ar71xx target has been retired and replaced by the
ath79 target. For example, you may have a node that was previously running an
ar71xx firmware version but you installed the latest Stable Release or Nightly Build which upgraded it to an
ath79 firmware target. In this case you will need to do a fresh First Install using the legacy architecture’s firmware.
- Use the AREDN Firmware Selector to download the previous release’s install files. For example, if your Ubiquiti Rocket M5 XW is currently running version
22.214.171.124, then download the files required for a First Install from release
126.96.36.199which used ar71xx (as shown below).
- Review the Installing AREDN Firmware documentation and follow the steps for the First Install procedure that is appropriate for your node model.
- For Ubiquiti and TP-LINK models you will be uploading the FACTORY firmware.
- For Mikrotik models you will boot using the KERNEL file (which you rename to rb.elf) and then immediately apply the SYSUPGRADE firmware image.
- For GL.iNet models you will use the recovery procedure to upload the SYSUPGRADE firmware image.
Another possible way to downgrade firmware between architectures is to enable Dangerous Upgrade under the Advanced Configuration settings. Setting this to ON will disable the normal firmware compatibility checks that are done automatically during the firmware install process. This should allow your node to install a firmware image that uses a legacy architecture.
After downgrading your node’s firmware you will then continue the process for entering your callsign and configuring the node’s settings, as explained in the Basic Setup section.